Hydraulic brake

From WOI Encyclopedia Italia

.

The hydraulic brake is an arrangement of braking mechanism which uses hydraulic fluid, typically some type of light-viscosity petroleum oil, to transfer pressure from the controlling unit, which is usually near the operator of the vehicle, to the actual brake mechanism, which is usually at or near the wheel of the vehicle.

The most common arrangement of hydraulic brake, found on most automobiles, consists of a brake pedal, a master cylinder, hydraulic lines, a "slave cylinder", and the braking unit.

General operation

When the brake pedal is depressed, leverage multiplies the force applied from the pedal to a piston in the master cylinder.

As force is applied to lines to the slave cylinders.

The two most common arrangements of slave cylinder are a pair of opposed pistons which are forced apart by the fluid pressure, (drum brakes) and a single piston which is forced out of its housing (disc brakes.)

The pistons then apply pressure to the braking mechanism, whether shoes inside a drum, or pads which compress on a disc.

Component specifics

(For typical light duty automotive braking systems.)

The brake pedal is a simple lever. It is attached at one point to the framework of the automobile, a rod extends from a point along its length to the master cylinder, and the pedal is at the end of the lever.

The master cylinder is divided internally into two sections, each of which pressurizes a separate hydraulic line. The forward segment applies pressure to the front brakes, and the rearmost segment to the rear brakes. This arrangement is made partly to balance the braking effect between the front and rear wheel sets, and partly for safety reasons: If one system fails, all braking ability is not lost; the other set can stop the vehicle. A master cylinder may use differing diameters between the two pistons to allow for increased fluid volume to one set of slave cylinders or the other.

Many modern hydraulic brake systems have a "Vacuum-assist" module which is attached between the master cylinder and the brake pedal and multiplies the braking force applied. Typically described as a vacuum booster, these units consist of a hollow housing with a moveable rubber diaphragm across the center, creating two chambers. When attached to the low-pressure portion of the throttle body or intake manifold of the engine, the pressure in both chambers of the unit is lowered. The equilibrium created by the low pressure in both chambers keeps the diaphragm from moving until the brake pedal is depressed. A return spring keeps the diaphragm in the starting position until the brake pedal is applied. When the brake pedal is applied, the movement opens an air valve which lets in atmospheric pressure air to one chamber of the booster. Since the pressure becomes higher in one chamber, the diaphragm moves toward the lower pressure chamber with a force created by the area of the diaphragm and the differential pressure. This force, in addition to the driver's foot force, pushes on the master cylinder piston. The diaphragm will stop moving when the forces on both sides of the chamber reach equilibrium. This can be caused by either the air valve closing (due to the pedal apply stopping) or if "runout" is reached. Runout occurs when the pressure in one chamber reaches atomospheric pressure and no additional force can be generated by the now stagnant differential pressure. After the runout point is reached, only the driver's foot force can be used to further apply the master cylinder piston.

The fluid pressure from the master cylinder travels through a pair of steel lines to a compensator, which performs two functions: It equalizes pressure between the two systems, and it provides a warning if one system loses pressure. The compensator has two chambers (to which the hydraulic lines attach) with a piston between them. When the pressure in either line is balanced, the piston does not move. If the pressure on one side is lost, the pressure from the other side moves the piston. When the piston makes contact with a simple electrical probe in the center of the unit, a circuit is completed, and the operator is warned of a failure in the brake system.

From the compensator, steel lines carry the pressure to the brake units at the wheels. Since the wheels do not maintain a fixed relation to the automobile, it is necessary to use flexible lines at the pivoting areas. Allowing steel lines to flex invites metal fatigue and, ultimately, brake failure.

Steel lines are preferred for most of the system for their rigidity; any amount of bulging or pressure induced distortion in the lines when pressure is applied results in less useful volume and pressure of fluid reaching the slave cylinders, and thus, reduced braking effectiveness. Bundy tube is often used in cars. Flexible lines are usually rubber hoses surrounded by steel braid, then coated with rubber to avoid weather damage to the steel.

Finally, the fluid pressure enters the Slave Cylinders and use one or more pistons to apply force to the braking unit.

Special considerations

Hydraulic systems are used where space restrictions must be considered. Air brake systems are bulky, and require air compressors and reservoir tanks for their operation. Hydraulic systems are relatively smaller and less expensive.

Hydraulic fluid must be non-compressible. Unlike air systems, where a valve is opened, and air is allowed to surge in to the lines and brake chambers until the pressure rises sufficiently, hydraulic systems rely on a single stroke of a piston to force hydraulic fluid through the system. If any sort of vapor is introduced into the system, it will compress, and fluid pressure in the system may not rise sufficiently to actuate the brakes. This can lead to loss of control of the vehicle.

Hydraulic braking systems are sometimes subjected to high temperatures during operation in extreme environments such as when descending steep grades. For this reason, hydraulic fluid must resist vaporization under temperature extremes. Water vaporizes easily with heat, and can corrode the metal parts of the system. If it gets into the brake lines, it can degrade brake performance dramatically. This is the reason for the common use of light oils as hydraulic fluids; oil displaces water and coats metal parts, protecting them against corrosion, and it can tolerate much higher temperatures before vaporizing.

"Brake Fade" is a condition caused by overheating in which braking effectiveness fades, and ultimately is lost. It may occur for a number of reasons: The pads which engage the rotating part may become overheated and "glaze over" (Become so smooth and hard that they cannot grip the metal sufficiently to slow the vehicle), vapor may be introduced to the system by vaporization of the hydraulic fluid under temperature extremes, and thermal distortion may cause the pads to change their shape and engage less surface area of the rotating part. Thermal distortion may also cause permanent changes in the shape of the metal parts, resulting in a reduction in braking capability that is irreparable without complete replacement of the affected parts.

Articles relating to Automobile configurations
Car body style and classification	2 plus 2 \| Antique car \| Cabrio coach \| Cabriolet \| City car \| Classic car \| Compact car \| Compact performance car \| Compact SUV \| Convertible \| Coupé \| Coupé convertible \| Coupe Utility \| Crossover SUV \| Custom car \| Drophead coupe \| Fastback \| Full-size car \| Grand tourer \| Hardtop \| Hatchback \| Hot hatch \| Hot rod \| Large family car \| Leisure activity vehicle \| Liftback \| Limousine \| Luxury car \| Microcar \| Mid-size car \| Mini SUV \| Minivan \| Multi-purpose vehicle \| Muscle car \| Notchback \| Personal luxury car \| Pickup truck \| Retractable hardtop \| Roadster \| Sedan \| Saloon \| Small family car \| Sport compact \| Sports car \| Sport utility vehicle \| Spyder \| Station wagon \| Estate car \| Supermini \| Targa top \| Taxicab \| Touring car \| Town car \| T-top \| Ute \| Van \| Voiturette
Specialised vehicles	Gyrocar \| Flying car. Amphibious vehicle
Fuel technologies	Internal combustion engine \| Electric vehicle \| Neighborhood electric vehicle \| Hybrid vehicle \| Battery electric vehicle \| Hydrogen vehicle \| Fuel cell \| Plug-in hybrid electric vehicle \| Steam car \| Alternative fuel cars \| Biodiesel \| Gasohol \| Ethanol \| LPG (Propane) \| Homogeneous Charge Compression Ignition \| Liquid Nitrogen \| Gasoline Direct Injection
Driven wheels	Four-wheel drive \| Front-wheel drive \| Rear-wheel drive \| All-wheel drive \| Two-wheel drive
Engine positioning	Front engine \| Rear engine \| Mid engine
Layout	FF layout \| FR layout \| MR layout \| MF layout \| RR layout
Engine configuration	Internal combustion engine \| Straight-6 \| V engine \| Wankel engine \| Reciprocating engine \| Inline engine \| Flat engine \| Flathead engine \| Diesel engine \| Two-stroke cycle \| Four-stroke cycle \| Pushrod engine \| Straight engine \| H engine \| Turbodiesel \| Hybrid vehicle \| Rechargeable energy storage system \| Electric vehicle \| Hydrogen vehicle

Body	Framework	A-pillar \| Bumper \| Cabrio coach \| Chassis \| Crumple zone \| Body-on-frame \| Dagmar bumpers \| Fender \| Fender skirts \| Grille \| Hood \| Hood scoop \| Monocoque construction \| Pontoon fenders \| Quarter panel \| Shaker scoop \| Spoiler \| Subframe \| Tonneau
Doors	Butterfly doors \| Gull-wing door \| Scissor doors \| Suicide door
Glass	Sunroof \| Greenhouse \| Windshield
Other	Antenna ball \| Hood ornament \| Japan Black paint \| Nerf bar \| Truck accessory \| Bumper sticker
Exterior Equipment	Lighting	Daytime running lamp \| Headlamp \| Headlight styling \| Hidden headlamps \| Retroreflector \| Sealed beam \| Trafficators \| High intensity discharge
Exterior Equipment	Other	British car number plates \| Distance sensor \| US and Canadian license plates \| Vanity plate \| Vehicle registration plate \| Windscreen wiper \| Windshield washer fluid
Car engine	Air/Fuel	Air filter \| Automatic Performance Control \| Blowoff valve \| Boost \| Boost controller \| Butterfly valve \| Carburetor \| Charge cooler \| Centrifugal type supercharger \| Cold air intake \| Engine management system \| Engine Control Unit \| Forced induction \| Front mounted intercooler \| Fuel filter \| Fuel injection \| Fuel pump \| Fuel tank \| Gasoline direct injection \| Indirect injection \| Intake \| Intercooler \| Manifold \| Manifold vacuum \| Mass flow sensor \| Naturally-aspirated engine \| Ram-air intake \| Scroll-type supercharger \| Short ram air intake \| Supercharger \| Throttle body \| Top mounted intercooler \| Turbocharger \| Turbocharged Direct Injection \| Twin-turbo \| Variable Length Intake Manifold \| Variable geometry turbocharger. Warm air intake
	Exhaust	Catalytic converter \| Emissions control devices \| Exhaust pipe \| Exhaust system \| Glasspack \| Muffler \| Oxygen sensor
	Cooling	Aircooling \| Antifreeze \| Ethylene glycol \| Radiator \| Thermostat
	Ignition system	Starter \| Car battery \| Contact breaker \| Distributor \| Electrical ballast \| Ignition coil \| Lead-acid battery \| Magneto \| Spark-ignition \| Spark plug
	Other	Balance shaft \| Block heater \| Crank. Cam \| Camshaft \| Connecting rod \| Combustion chamber \| Crank pin \| Crankshaft \| Crossflow cylinder head \| Crossplane \| Desmodromic valve \| Engine knocking \| Compression ratio \| Crank sensor \| Cylinder \| Cylinder bank \| Cylinder block \| Cylinder head \| Cylinder head porting \| Dump valve,Engine balance \| Oil filter \| Firing order \| Freeze plug \| Gasket \| Head gasket \| Hypereutectic piston \| Hydrolock \| Lean burn \| Main bearing \| Motor oil \| Multi-valve \| Oil sludge \| Overhead camshaft \| Overhead valve \| PCV valve \| Piston \| Piston ring \| Pneumatic valve gear \| Poppet valve \| Power band \| Redline \| Reverse-flow cylinder head \| Rocker arm \| Seal \| Sleeve valve \| Starter ring gear \| Synthetic oil \| Tappet \| Timing belt \| Timing mark \| Top dead centre \| Underdrive pulleys \| Valve float \| Variable valve timing
Interior equipment	Instruments	Backup camera \| Boost gauge \| Buzzer \| Car computer \| Carputer \| Check Engine light \| Fuel gauge \| Global Positioning System \| Idiot light \| Navigation system \| Odometer \| Speedometer \| Tachometer \| Trip computer
	Controls	Bowden cable \| Cruise control \| Electronic throttle control \| Hand brake \| Manettino dial \| Steering wheel \| Throttle \| Gear stick
	Motor vehicle theft deterrence	Car alarm \| ESITrack \| Immobiliser \| Klaxon \| Vehicle tracking system \| VIN etching
	Passenger safety & seating	Airbag \| Armrest \| Automatic seatbelt \| Bench seat \| Bucket seat \| Child safety lock \| Dicky seat \| Passive safety \| Rumble seat \| Seat belt
	Other	Air conditioning \| Ancillary power \| Car audio \| Car phone \| Center console \| Dashboard \| Motorola connector \| Power window \| Rear-view mirror \| TripSense
Powertrain	Wheels and Tires	All-terrain tyre \| Bias-ply tire \| Contact patch \| Custom wheel \| Drive wheel \| Hubcap \| Magnesium alloy wheel \| Mud-terrain tyre \| Paddle tires \| Radial tire \| Rostyle wheel \| Run flat tires \| Schrader valve \| Slick tire \| Spinner \| Tire code \| Tread \| Treadwear rating \| Whitewall tire \| Wire wheels
	Transmission	Automatic transmission \| Clutch \| Continuously variable transmission \| Differential \| Driveshaft \| Electrorheological clutch \| Epicyclic gearing \| Fluid coupling \| Fully-automatic transmission \| Gear stick \| Gearbox \| Hydramatic \| Limited slip differential \| Locking differential \| Manual transmission \| Roto Hydramatic \| Saxomat \| Semi-automatic transmission \| Semi-automatic transmission \| Super Turbine 300 \| Tiptronic Torque converter \| Transmission (mechanics) \| Transmission Control Unit \| Turbo-Hydramatic \| Universal joint
	Steering	Ackermann steering geometry \| Anti-lock braking system \| Camber angle \| Car handling \| Caster angle \| Oversteer \| Power steering \| Rack and pinion \| Toe angle \| Torque steering \| Understeer
	Suspension	Axle \| Beam axle \| Coil spring \| De Dion tube \| Double wishbone \| Electronic Stability Control \| Hydragas \| Hydrolastic \| Hydropneumatic suspension \| Independent suspension \| Kingpin \| Leaf spring \| Live axle \| MacPherson strut \| Multi-link suspension \| Panhard rod \| Semi-trailing arm suspension \| Shock absorber \| Sway bar \| Swing axle \| Torsion beam suspension \| Transaxle \| Trailing arm \| Unsprung weight \| Watt's linkage \| Wishbone suspension
	Brakes	Anti-lock braking system \| Disc brake \| Drum brake \| Hand brake \| Hydraulic brake \| Inboard brake \| Brake lining \| Brake fade \| Brake fluid \| Hydraulic fluid \| Brake bleeding \| Engine braking \| Electronic brakeforce distribution \| Regenerative brake

Hydraulic brake

From WOI Encyclopedia Italia

Contents

General operation

Component specifics

Special considerations

See also

Views

Personal tools

Navigation

Search

Toolbox